Best Barns mansfield_1212df Bedienerhandbuch

Manufactured by Reynolds Building Systems, Inc.205 Arlington Drive Greenville, PA 16125 724-646-3775This manual is copyrighted. Under the copyright

71-1/2" HeaderSupportSiding 1/2" Below Top Plate3. Cut (2) two more 34-3/4" plates from 58-1/2" long2x4s and assemble another wall

Drawing shows a buildingwith the doors offset.Step 9A Set Walls - Doors Offset1. Secure wall panels together at the corners. Use (4) four 10d coated n

Drawing shows a buildingwith the doors centered.2x4 Door HeaderStep 9B Set Walls - Doors Centered1. Secure wall panels together at the corners. Use (4

flush3. Install trim on the opposite end of the building.2. Install gable on the opposite sidewall.Step 11 Install GableStep 10 Install Sidewall TrimI

1. Cut a 2x4-6' in half and install a 3' piece over the frontwall, against the left gable plate. Use 10d sinkers.2. Install a 6' long 2

Inside of BuildingFront Wall2x4 Tie PlateStep 13 Layout Roof Trusses1. Layout the truss spacing from the left of the building. Measure from the backsi

3. Install soffit panels on theopposite side. Start with a24" long panel that has a'LAP' edge.Step 14 Set Roof TrussesRear GableSet roo

Optional ridge vent providesideal ventilation.AirSpaceTrussShingles2x4 Truss3. Install 1x6 fascia trim. Cut 84" long piece to fit.Step 16 Install

AirSpaceTrussShingles1x6 FasciaFeltPaper1x6 Gable Trim1. Install 1x6-87" long gable trim over the 2x4s on both gable. Install trim flushwith the

Step 18 Install Doors & Hardware4. Before you fasten the hinges to the doortrim, temporarily prop the doors in theopening. Leave a space at the to

Tongue EdgeLAP EdgeHammer & Hand SawFraming Square & LevelPower Circular SawPower Drill/screwdriverMeasuring Tape2 - 8' Step LaddersIMPOR

Material Packaged In Component Kit3 1 lb. box 10d Sinkers3 1 lb. box 8d Galv.2 1 lb. box 7d Sinkers1 1 lb. box 6d Galv.3 1 lb. box 6d Common1 1 l

12' - 0" Building WidthTo keep 2x4 frame frommoving, toe nail to 4x4.DOOR WALLXXXXXX16"15-1/4"2x4 Joist HeaderXX16"Shown belo

Step 1 Assemble TrussesBuilding Tip: To aid in the assembly of the trusses, temporarily screw 2x4 blocks tothe floor. There are short 2x4s, that may h

72" long 2x43/4" Plywood GussetStep 2 Assemble Roof Gables1. Butt (2) two 72" long 2x4s together and secure by nailing a 3-1/2" x

5. Install siding and 2x4son the other gable frame.4. Install 86-1/4" long 2x4s flush with the top of the gable frame.Use 10d sinkers.2. Install

AABBXXXXXX2. Install 72" wall studs between the top and bottom plates. Assemble wall frames with10d sinkers, two (2) nails at each stud end. Nail

XXXXXXXX72" Wall PlateXXXXXXXXSiding 1/2" BelowTop PlateStep 5 Assemble 12' Long SidewallsSiding Extends 3/4" Below PlateLAP Edge1

3. Install a 71-1/2" long 2x4 [red ends], asa header support, on each wall frame.71-1/2" HeaderSupport5. Install 16" siding panel with