Manufactured by Reynolds Building Systems, Inc.205 Arlington Drive Greenville, PA 16125 724-646-3775This manual is copyrighted. Under the copyright
nailnailStep 9 Assemble 12' Door Wall1. Gather the material listed below to assemble the door wall.6 Pre-cut Wall Studs4 2x4-6' Boards1 Door
6. Cut and remove the bottom 2x4 in the door opening.Step 10 Set Wall Panels1. Set the back wall panel between the sidewalls. Secure wall panels toget
flush3. Install 95" long 1x4 white pine trimboards as corner trim to the rearwalls. Install trim flush with thesiding on the sidewalls.4. Repeat
1x4 Trim24"22-3/8"Back of BuildingImportant: When installing trussesplace the gusset on the line.When marking the wall plates, placethe &apo
Secure the trusses to the sidewall thathas the wall bracing first. Make surethe opposite sidewall is straight beforesecuring trusses. The building wid
5. Install (2) two 6' long soffit panels.6. Install 4' long soffit panels to finish.SoffitStep 17 Install Sidewall Trim & Soffit96-3/4&a
1. Install a 121-1/2" long 1x6 trim board at the rear of the building, flush with the face of the 2x4.Install the 1x6 board so the face of the bo
Back Wall1x6 Gable Trim48" x 96"Plyclip48" x 48"48" x 96"3. Install 1x6 trim on the rear gable, flushwith the top of the
VIEW FROM INSIDECut leftover wall bracing and install 2x4s around the door opening against the 1x6 door jamb.2x4 BoardsStep 21 Install 2x4 Jamb Suppor
Supplement DetailsPre-built Header1. If you purchased the optional entry door, locate where you want the opening to be andinstall the 37-1/2" doo
Tongue EdgeLAP EdgeTool ListHammer & Phillips ScrewdriverFraming Square & LevelHand or Circular SawAlways wear safety glasses when cutting or
Optional Roof Covering15 bdl. Roof Shingles10 pcs. Roof 'drip' Edge-10'Material Suppliedby Local Supplier11 Truss Bottom 2x4 144"
2. Cut (13) thirteen 2x4-12' floor joist to 11'-9". Treated lumber may be thicker than 1-1/2". Takethis into account when cutting
1. From our 12' long lumber carton, locate a 2x4-12' board thathas angle cuts on both ends. Use this boards as a pattern andcut two (2) more
Step 2 Assemble Roof Gables2. Install 38-3/4" and 50" long 2x4 gable studs. Securegable studs with 1" x 4" metal drive-on plates.3
Step 3 Install Siding on Gables1. Cut a 4x8 siding panel in half creating (2) two 48" siding panels. Install one of the pieces withthe 'LAP
XXXXXXXXXXXXXXXXStep 5 Assemble 12' Back WallLAPEdge4. Square wall frame. Measure the wall diagonally (corner to corner). Then measure the oppos
XXXXXXXXStep 6 Assemble 140-1/2" Long Sidewalls4. Square wall frame. Install the first siding panel with the 'LAP edge' extending3-1/2&
XXXXXXXXStep 8 Assemble Door Header1. Locate (2) two 2x10-10' boards.2. Cut these boards to a length of 99".3. Cut filler boards from leftov
Kommentare zu diesen Handbüchern