Manufactured by Reynolds Building Systems, Inc.205 Arlington Drive Greenville, PA 16125 724-646-3775This manual is copyrighted. Under the copyright
4. Repeat to apply siding to the other 10' wall frame.Step 6 Assemble Sidewalls for 20' Building Length1. Select one of the 10' sidewal
2x4-7' Wall Studs19" Bottom Wall Plate3. Repeat to assemble another wall frame.Mark 'Right Frontwall'Mark 'Left Frontwall&apo
Step 8 Set Walls2x4 Wall Brace1. Set wall panels. Secure at corners with 10d sinkers (4 nails per corner). Secure to floorwith 10 sinkers. Disassemble
SideWallFlush AcrossTop Plate1x4 Trim87-3/4" Long 1x4 Corner Trim1. Install 87-3/4" long 1x4 corner trim boards to the rear wall. Install tr
1. Install a gable on the rear wall. The gable siding will extend over the 1x4 trimon the lower wall. NOT behind the trim!Secure gable to wall by nail
1. Install a 2x4-6' board over the sidewall,against the rear gable plate. Use 10dsinkers.SidewallStep 12 Install 2x4 Tie Plates2x4-6' Tie Pl
Inside of Building2x4 Tie PlateStep 13 Layout Roof Trusses1. Layout the truss spacing from the rear of the building. Measure from the inside of the re
3. Install soffit panels on theopposite side. Start with a24" long panel that has a'LAP' edge.Step 14 Set Roof TrussesRear GableStep 15
SOFFIT BLOCK DETAILWhen installing 1x6 fascia, next step, it will be necessary to install 22-1/2" long 2x4blocks between trusses where the fascia
Step 17 Install Roof Sheathing48" x 72"48" x 48"48" LongPanel2. Install a 1x6 - 7' fascia board. Install a 22-1/2"
Tool ListHammer & Phillips ScrewdriverFraming Square & LevelCircular Saw and/or Hand SawPower Drill/ScrewdriverMeasuring Tape & Chalkline2
Step 18 Install Front SoffitSoffit Panels1x6 Gable TrimIf you ordered the optional floor, install thegalvanized door sill. Secure sill with panhead sc
VIEW FROM INSIDEStep 19 Install 2x4 Around Door JambPrime Door Jamb2x4-7'51-1/2" Long 2x41. Install a 2x4 - 7' on the inside of the doo
AirSpaceTrussShingles1x6 FasciaFeltPaper1x3 Gable TrimFrame Door OpeningOSB Filler37-1/2" Long 2x42. Install shingles according to the instructio
Material Packaged In Lumber Kit7 Collar Ties 2x4 90"22 Truss Rafters 2x4 86-1/4"35 Wall Studs 2x4 84"2 Double Studs 2x4 84"18 Wall
Material Packaged In Siding & Roof Sheathing KitRoof Covering - not supplied in kit12 bdl. Roof Shingles9 pcs. Roof 'drip' Edge 10&apo
Optional Wood Floor System6. Cut all the 2x4-12' boards to 11'-9". These boards will be the floor joist. Treated lumbermay be thicker t
Notes To Floor4x84x84x84x411. Square the floor. See note below. The anglemeasurement should be 23' - 4". Nail severalfloor joist to the 4x4
Step 1 Assemble Trusses1. Screw (2) two 2x4 blocks to the 12' wide end of the floor at the corner, see below.2. Place two truss legs together. Po
Step 2 Assemble Roof Gables1. Butt (2) two 72" long 2x4s together and secure by nailing a 3-1/2" x 31-3/4" long ply-wood gusset across
2. Install gable siding using 6d galv. nails acrossthe top of the gable frame. Use 8d galv. nailsalong the bottom edge. See Note Below. *B3. Install s
AABBXXXXXX2. Install 7' wall studs between the top and bottom plates. Assemble wall frames with10d sinkers, two (2) nails at each stud end. Nail
If you are installing the optional walk-in door see the instructionsat the back of the book.Step 5 Assemble 10' Long Sidewalls4. Square wall fram
Kommentare zu diesen Handbüchern